Plumbing Basics: The First Step for When Installing a Bathtub
Plumbing Basics: The First Step for When Installing a Bathtub
Blog Article
We've unearthed the article involving Installing A Bathtub listed below on the internet and accepted it made perfect sense to relate it with you on my blog.
Setting up a bathtub isn't precisely rocket science, yet it does need solid plumbing, woodworking, and sometimes, tiling abilities. Replacing an old bath tub with a new one is additionally a moderately tough job. If the old tub is conveniently available, the task can relocate speedily; if you have to open a wall surface to eliminate the old tub and place the new tub, the task is a lot harder. In either instance, the task is within a home handyman's abilities, although you will require an assistant to leave the old tub as well as set in the brand-new one. Make certain you have actually certified yourself for the task as well as fit attempting it. As opposed to employing a professional to take control of a halfway-completed project, it is far better to take into consideration employing one prior to you begin. Chances are you may need an expert plumber to make tube connections.
This short article will aid you install a brand-new tub in your restroom if you have actually currently purchased a new tub as well as do not require to change the arrangement of your previous water system pipelines.
Your tools and also material list need to consist of the following:
Getting ready for the Setup
First of all, the sustaining frame provided with the bathroom ought to be fitted (if called for) according to the manufacturer's guidelines. Next, fit the taps or mixer to the bathtub. When suitable the tap block, it is essential to make certain that if the faucet features a plastic washing machine, it is fitted between the bathroom and also the faucets. On a plastic bath, it is also reasonable to fit a supporting plate under the faucets unit to avoid pressure on the bathtub.
Fit the versatile faucet connectors to the bottom of the two faucets using 2 nuts and also olives (in some cases supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the outlet with the hole in the bathroom. Make use of the nut provided by the manufacturer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bath. Make sure you make use of all of the provided washers.
Attach the catch to the bottom of the waste outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom need to currently prepare to be suited its last placement.
Removing Old Taps
If you need to change old faucets with new ones as a part of your setup, then the first thing you need to do is separate the water. After doing so, turn on the faucets to drain any kind of water continuing to be in the system. The procedure of getting rid of the existing faucets can be rather troublesome because of the restricted accessibility that is typically the instance.
Utilize a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipes to the taps. Have a fabric all set for the continuing to be water that will certainly originate from the pipes. Once the supply pipes have been removed, utilize the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will require to stop the solitary faucets from transforming during this process. When the taps have been removed, the holes in the bath/basin will certainly have to be cleaned of any kind of old securing compound.
Before proceeding to fit the brand-new taps, contrast the pipeline links on the old faucets to the new taps. If the old taps are longer than the brand-new taps, after that a shank adapter is needed for the brand-new faucets to fit.
Installing the Bath tub
Utilizing both wood boards under its feet, put the bath tub in the needed position. The wooden boards are useful in evenly spreading the weight of the tub over the area of the boards instead of concentrating all the weight onto four little points.
The following objective is to make certain that the tub is leveled all round. This can be attained by checking the level as well as adjusting the feet on the bath tub until the spirit level checks out degree.
To set up taps, fit the bottom of the furthest adaptable tap connector to the suitable supply pipe by making a compression sign up with; then do the same for the various other faucet.
Turn on the water as well as inspect all joints and also brand-new pipework for leakages and tighten them if required. Load the bathtub and likewise examine the overflow electrical outlet and also the typical electrical outlet for leakages.
Lastly, deal with the bath paneling as defined in the manufacturer's user's manual. Tiling and securing around the tub must wait up until the bathtub has actually been made use of at the very least once as this will resolve it right into its last position.
Suitable New Touches
If the tails of the brand-new taps are plastic, then you will certainly need a plastic connector to prevent damage to the thread. One end of the connector fits on the plastic tail of the tap and also the other end gives a link to the current supply pipes.
If you require to fit a monobloc, after that you will certainly need minimizing couplers, which connects the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next off, place the tap in the mounting hole in the bath/basin ensuring that the washing machines remain in location in between the tap and also the sink. Safeguard the tap in place with the supplier supplied backnut. As soon as the tap is firmly in position, the supply pipelines can be attached to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with typical tap connectors. The previous type ought to be attached to the faucet ends first, tightening only by hand. The supply pipes can later on be linked to the other end. Tighten up both ends with a spanner after both ends have actually been attached.
Tiling Around the Tub
In the area where the bath fulfills the ceramic tile, it is necessary to secure the accompanies a silicone rubber caulking. This is necessary as the fitting can move enough to break an inflexible seal, causing the water to permeate the wall surface between the bathroom as well as the tiling, bring about problems with dampness and also feasible leaks to the ceiling listed below.
You can select from a variety of coloured sealants to blend in your components and also fittings. They are offered in tubes and cartridges, and can sealing voids approximately a width of 3mm (1/8 inch). If you have a bigger void to fill up, you can fill it with spins of soaked newspaper or soft rope. Bear in mind to constantly fill the bathtub with water prior to securing, to permit the movement experienced when the tub is in use. The sealer can fracture fairly very early if you do not consider this activity before securing.
Additionally, ceramic coving or quadrant tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are likewise easily available on the market. It is advisable to fit the ceramic tiles utilizing water-resistant or water-proof glue and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We are very inquisitive about How to Install a Bathtub Yourself and I'm hoping you enjoyed reading our blog entry. Remember to take a moment to share this content if you enjoyed it. Thanks so much for your time spent reading it.
Reliable? That's us! Report this page